新浪博客

ABB_800xA学习笔记189：System_800xA_Control_6.0_AC_800M_Getting_Started_29-第四章硬件配置3

2023-11-28 18:26阅读：

http://blog.sina.cn/dpool/blog/u/1916946105

继续学习第四章
Reading I/O addresses from the Application
从应用程序读取IO地址
An easy way to read the I/O address is to open (in this case) Diagram2 in the program editor and check the column labeled I/O Address. Here you will find the address for the photocell and the motors (see Figure 39).
读取IO地址简单的方法是在图表编辑器打开图表2（这个例子中），检查IO地址列。在这你可以看到光电管和电机的地址（见图39）
ABB_800xA学习笔记189：System_800xA_Control_6.0_AC_800M_Getting_Started_29-第四章硬件配置3
Figure 39. The I/O Address column shows how variables are connected to I/O channels
图 39. IO地址列显示变量如何连接到IO模板
Changes made to I/O connections in the hardware editor will be reflected in both
br>editors.
在硬件编辑器中修改IO连接会影响两边的编辑器。
Your project has now been tested offline and the hardware configuration is complete.
你的项目已经脱机测试，硬件配置完成。


Releasing Reservations
释放保留
Since you have finished the configuration, you can release any reservations.
一旦完成配置，可以释放任何保留。
1. Right-click MyDoors, and select Release Reservation
右键点击MyDoors，选择释放保留
2. The displayed dialog box is used to release reserved entities. In this example, the default selection is sufficient. However, you can enter a comment.
弹出的对话框用域释放保留的实体。在这个例子，默认的选择足以。但是你可以输入注释。
ABB_800xA学习笔记189：System_800xA_Control_6.0_AC_800M_Getting_Started_29-第四章硬件配置3
Figure 40. Releasing reservations
图 40. 释放保留
3. Click OK. The reservations are released.
点击OK按钮。保留被释放
If you use environments, continue by deploying the configuration (described below). Otherwise, you are ready to proceed with Section 5, Connecting theController and Go Online.
如果使用了环境，请继续部署配置（如下描述）。否则，你可以继续执行第五章，连接控制器，到在线模式。
Deploying Configuration Changes
部署配置修改
This section is only valid when using environments
此章节只有使用环境才有用。
When you have released the reservations, you deploy the changes from the Engineering Environment to the Production Environment.
当你释放了保留，你从工程环境部署修改到生产环境。
1. Right-click MyDoors project, and select Deploy
右键点击MyDoors项目，选择部署
The displayed dialog box is used to select relevant destination environment, and what entities to deploy.
部署对话框用于选择相关目标环境以及要部署的实体。
ABB_800xA学习笔记189：System_800xA_Control_6.0_AC_800M_Getting_Started_29-第四章硬件配置3
Figure 41. Deploy changes.
图 41. 部署修改
2. Click Deploy. The project and all other modified entities are deployed to the Production Environment.
点击部署。项目和所有的其它修改过的实体被部署到生产环境。
You are now ready to proceed with Section 5, Connecting the Controller and Go Online.
你现在准备执行第五章，连接到控制器，转在线。

我的更多文章

下载客户端阅读体验更佳

APP专享